Lenovo Air Conditioner S2110A User Manual

IdeaTab S2110A  
Hardware  
Maintenance  
Manual  
 
Contents  
Handling devices that are sensitive to  
Important notice for replacing a system  
Important information about replacing RoHS  
iii  
 
About this manual  
This manual contains service and reference information for the following  
Lenovo product:  
Lenovo IdeaTab S2110A  
Use this manual to troubleshoot problems.  
The manual is divided into the following sections:  
• The common sections provide general information, guidelines, and safety  
information required for servicing computers.  
• The product-specific section includes service, reference, and product-specific  
parts information.  
Important:  
This manual is intended only for trained servicers who are familiar with  
Lenovo products. Use this manual to troubleshoot problems effectively.  
Before servicing a Lenovo product, make sure to read all the information  
iv  
 
 
Lenovo IdeaTab S2110A Hardware Maintenance Manual  
General safety  
Follow these rules below to ensure general safety:  
• Observe a good housekeeping in the area where the machines are put during  
and after the maintenance.  
• When lifting any heavy object:  
1. Make sure that you can stand safely without slipping.  
2. Distribute the weight of the object equally between your feet.  
3. Use a slow lifting force. Never move suddenly or twist when you attempt  
to lift it.  
4. Lift it by standing or pushing up with your leg muscles; this action could  
avoid the strain from the muscles in your back. Do not attempt to lift any  
object that weighs more than 16 kg (35 lb) or that you think is too heavy for  
you.  
• Do not perform any action that causes hazards to the customer, or that makes  
the machine unsafe.  
• Before you start the machine, make sure that other service representatives  
and the customer are not in a hazardous position.  
• Place removed covers and other parts in a safe place, keeping them away  
from all personnel, while you are servicing the machine.  
• Keep your toolcase away from walk areas so that other people will not trip it  
over.  
• Do not wear loose clothing that can be trapped in the moving parts of the  
machine. Make sure that your sleeves are fastened or rolled up above your  
elbows. If your hair is long, fasten it.  
• Insert the ends of your necktie or scarf inside clothing or fasten it with the  
nonconductive clip, about 8 centimeters (3 inches) from the end.  
• Do not wear jewelry, chains, metal-frame eyeglasses, or metal fasteners for  
your clothing.  
Attention: Metal objects are good electrical conductors.  
Wear safety glasses when you are hammering, drilling, soldering, cutting  
wire, attaching springs, using solvents, or working in any other conditions  
that may be hazardous to your eyes.  
• After service, reinstall all safety shields, guards, labels, and ground wires.  
Replace any safety device that is worn or defective.  
• Reinstall all covers correctly before returning the machine to the customer.  
• Fan louvers on the machine help to prevent the overheating of internal  
components. Do not obstruct fan louvers or cover them with labels or  
stickers.  
2
 
 
Safety information  
Electrical safety  
Observe the following rules when working on electrical equipments.  
Important:  
Use only approved tools and test equipments. Some hand tools have  
handles covered with a soft material that does not insulate you when  
working with live electrical currents.  
Many customers have rubber floor mats near their machines that contain  
small conductive fibers to decrease electrostatic discharges. Do not use such  
kind of mat to protect yourself from electrical shock.  
• Find the room emergency power-off (EPO) switch, disconnecting the switch  
or electrical outlet. If an electrical accident occurs, you can then operate the  
switch or unplug the power cord quickly.  
• Do not work alone under hazardous conditions or near the equipment that  
has hazardous voltages.  
• Disconnect all power before:  
– Performing a mechanical inspection  
– Working near power supplies  
– Removing or installing main units  
• Before you start to work on the machine, unplug the power cord. If you  
cannot unplug it, ask the customer to power-off the wall box that supplies  
power to the machine, and to lock the wall box in the off position.  
• If you need to work on a machine that has exposed electrical circuits, observe  
the following precautions:  
– Ensure that another person, familiar with the power-off controls, is near  
you.  
Attention: Another person must be there to switch off the power, if  
necessary.  
– Use only one hand when working with powered-on electrical equipment;  
keep the other hand in your pocket or behind your back.  
Attention: An electrical shock can occur only when there is a complete  
circuit. By observing the above rule, you may prevent a current from  
passing through your body.  
– When using testers, set the controls correctly and use the approved probe  
leads and accessories for that tester.  
– Stand on suitable rubber mats (obtained locally, if necessary) to insulate  
you from grounds such as metal floor strips and machine frames.  
Observe the special safety precautions when you work with very high voltages;  
instructions for these precautions are in the safety sections of maintenance  
information. Be extremely careful when you measure the high voltages.  
• Regularly inspect and maintain your electrical hand tools for safe operational  
condition.  
• Do not use worn or broken tools and testers.  
• Never assume that power has been disconnected from a circuit. First, check it  
to make sure that it has been powered off.  
3
 
 
Lenovo IdeaTab S2110A Hardware Maintenance Manual  
• Always look carefully for possible hazards in your work area. Examples of  
these hazards are moist floors, nongrounded power extension cables, power  
surges, and missing safety grounds.  
• Do not touch live electrical circuits with the reflective surface of a plastic  
dental mirror. The surface is conductive; such touching can cause personal  
injury and machine damage.  
• Do not service the following parts with the power on when they are removed  
from their normal operating places in a machine:  
– Power supply units  
– Pumps  
– Blowers and fans  
– Motor generators  
and similar units. (This practice ensures correct grounding of the units.)  
• If an electrical accident occurs:  
– Caution: do not become a victim yourself.  
– Switch off the power.  
– Send the victim to get medical aid.  
4
 
Safety information  
Safety inspection guide  
The purpose of this inspection guide is to assist you in identifying potential  
unsafe conditions. As each machine was designed and built, required safety  
items were installed to protect users and service personnel from injury. This  
guide addresses only those items. You should use good judgment to identify  
potential safety hazards according to the attachment of non-Lenovo features or  
options not covered by this inspection guide.  
If any unsafe conditions are present, you must determine how serious the  
apparent hazard could be and whether you can continue without first correcting  
the problem.  
Consider these conditions and the safety hazards they present:  
• Electrical hazards, especially primary power (primary voltage on the frame  
can cause serious or fatal electrical shock)  
• Explosive hazards, such as a damaged CRT face or a bulging capacitor  
• Mechanical hazards, such as loose or missing hardware  
To determine whether there are any potential unsafe conditions, use the  
following checklist at the beginning of every service task. Begin the checks with  
the power off, and the power cord disconnected.  
Checklist:  
1. Check exterior covers for damage (loose, broken, or sharp edges).  
2. Turn off the computer. Disconnect the power cord.  
3. Check the power cord for:  
a. A third-wire ground connector in good condition. Use a meter to measure  
third-wire ground continuity for 0.1 ohm or less between the external  
ground pin and the frame ground.  
b. The power cord should be the type specified in the parts list.  
c. Insulation must not be frayed or worn.  
4. Check for cracked or bulging batteries.  
5. Remove the cover.  
6. Check for any obvious non-Lenovo alterations. Use good judgment as to the  
safety of any non-Lenovo alterations.  
7. Check inside the unit for any obvious unsafe conditions, such as metal filings,  
contamination, water or other liquids, or signs of fire or smoke damage.  
8. Check for worn, frayed, or pinched cables.  
9. Check that the power-supply cover fasteners (screws or rivets) have not been  
removed or tampered with.  
5
 
 
Lenovo IdeaTab S2110A Hardware Maintenance Manual  
Handling devices that are sensitive to electrostatic discharge  
Any computer part containing transistors or integrated circuits (ICs) should be  
considered sensitive to electrostatic discharge (ESD). ESD damage can occur  
when there is a difference in charge between objects. Protect against ESD damage  
by equalizing the charge so that the machine, the part, the work mat, and the  
person handling the part are all at the same charge.  
Notes:  
1. Use product-specific ESD procedures when they exceed the  
requirements noted here.  
2. Make sure that the ESD protective devices you use have been certified  
(ISO 9000) as fully effective.  
When handling ESD-sensitive parts:  
• Keep the parts in protective packages until they are inserted into the product.  
Avoid contact with other people.  
Wear a grounded wrist strap against your skin to eliminate static on your  
body.  
• Prevent the part from touching your clothing. Most clothing is insulative and  
retains a charge even when you are wearing a wrist strap.  
• Use the black side of a grounded work mat to provide a static-free work  
surface. The mat is especially useful when handling ESD-sensitive devices.  
• Select a grounding system, such as those listed below, to provide protection  
that meets the specific service requirement.  
Notes:  
The use of a grounding system to guard against ESD damage is desirable but  
not necessary.  
– Attach the ESD ground clip to any frame ground, ground braid, or green-  
wire ground.  
– When working on a double-insulated or battery-operated system, use an  
ESD common ground or reference point. You can use coax or connector-  
outside shells on these systems.  
– Use the round ground prong of the ac plug on ac-operated computers.  
Grounding requirements  
Electrical grounding of the computer is required for operator safety and correct  
system function. Proper grounding of the electrical outlet can be verified by a  
certified electrician.  
6
 
   
Safety information  
Safety notices: multilingual translations  
The safety notices in this section are provided in English, French, German,  
Hebrew, Italian, Japanese, and Spanish.  
Safety notice 1  
Before the computer is powered on after FRU replacement, make sure all  
screws, springs, and other small parts are in place and are not left loose  
inside the computer. Verify this by shaking the computer and listening for  
rattling sounds. Metallic parts or metal flakes can cause electrical shorts.  
Avant de remettre l’ordinateur sous tension après remplacement d’une unité  
en clientèle, vérifiez que tous les ressorts, vis et autres pièces sont bien en  
place et bien fixées. Pour ce faire, secouez l’unité et assurez-vous qu’aucun  
bruit suspect ne se produit. Des pièces métalliques ou des copeaux de métal  
pourraient causer un court-circuit.  
Bevor nach einem FRU-Austausch der Computer wieder angeschlossen  
wird, muß sichergestellt werden, daß keine Schrauben, Federn oder andere  
Kleinteile fehlen oder im Gehäuse vergessen wurden. Der Computer muß  
geschüttelt und auf Klappergeräusche geprüft werden. Metallteile oder-  
splitter können Kurzschlüsse erzeugen.  
Prima di accendere l’elaboratore dopo che é stata effettuata la sostituzione di  
una FRU, accertarsi che tutte le viti, le molle e tutte le altri parti di piccole  
dimensioni siano nella corretta posizione e non siano sparse all’interno  
dell’elaboratore. Verificare ciò scuotendo l’elaboratore e prestando  
attenzione ad eventuali rumori; eventuali parti o pezzetti metallici possono  
provocare cortocircuiti pericolosi.  
Antes de encender el sistema despues de sustituir una FRU, compruebe que  
todos los tornillos, muelles y demás piezas pequeñas se encuentran en su  
sitio y no se encuentran sueltas dentro del sistema. Compruébelo agitando el  
sistema y escuchando los posibles ruidos que provocarían. Las piezas  
metálicas pueden causar cortocircuitos eléctricos.  
7
 
 
Lenovo IdeaTab S2110A Hardware Maintenance Manual  
Safety notice 2  
DANGER  
Some standby batteries contain a small amount of nickel and cadmium. Do  
not disassemble a standby battery, recharge it, throw it into fire or water, or  
short-circuit it. Dispose of the battery as required by local ordinances or  
regulations. Use only the battery in the appropriate parts listing. Use of an  
incorrect battery can result in ignition or explosion of the battery.  
Certaines batteries de secours contiennent du nickel et du cadmium. Ne les  
démontez pas, ne les rechargez pas, ne les exposez ni au feu ni à l’eau. Ne  
les mettez pas en court-circuit. Pour les mettre au rebut, conformez-vous à  
la réglementation en vigueur. Lorsque vous remplacez la pile de sauvegarde  
ou celle de l’horloge temps réel, veillez à n’utiliser que les modèles cités dans  
la liste de pièces détachées adéquate. Une batterie ou une pile inappropriée  
risque de prendre feu ou d’exploser.  
Die Bereitschaftsbatterie, die sich unter dem Diskettenlaufwerk befindet,  
kann geringe Mengen Nickel und Cadmium enthalten. Sie darf nicht  
zerlegt, wiederaufgeladen, kurzgeschlossen, oder Feuer oder Wasser  
ausgesetzt werden. Bei der Entsorgung die örtlichen Bestimmungen für  
Sondermüll beachten. Beim Ersetzen der Bereitschafts-oder Systembatterie  
nur Batterien des Typs verwenden, der in der Ersatzteilliste aufgeführt ist.  
Der Einsatz falscher Batterien kann zu Entzündung oder Explosion führen.  
Alcune batterie di riserva contengono una piccola quantità di nichel e  
cadmio. Non smontarle, ricaricarle, gettarle nel fuoco o nell’acqua né  
cortocircuitarle. Smaltirle secondo la normativa in vigore (DPR 915/82,  
successive disposizioni e disposizioni locali). Quando si sostituisce la  
batteria dell’RTC (real time clock) o la batteria di supporto, utilizzare  
soltanto i tipi inseriti nell’appropriato Catalogo parti. L’impiego di una  
batteria non adatta potrebbe determinare l’incendio o l’esplosione della  
batteria stessa.  
Algunas baterías de reserva contienen una pequeña cantidad de níquel y  
cadmio. No las desmonte, ni recargue, ni las eche al fuego o al agua ni las  
cortocircuite. Deséchelas tal como dispone la normativa local. Utilice sólo  
baterías que se encuentren en la lista de piezas. La utilización de una batería  
no apropiada puede provocar la ignición o explosión de la misma.  
8
 
Safety information  
Safety notice 3  
DANGER  
The battery pack contains small amounts of nickel. Do not disassemble it,  
throw it into fire or water, or short-circuit it. Dispose of the battery pack as  
required by local ordinances or regulations. Use only the battery in the  
appropriate parts listing when replacing the battery pack. Use of an  
incorrect battery can result in ignition or explosion of the battery.  
La batterie contient du nickel. Ne la démontez pas, ne l’exposez ni au feu ni  
à l’eau. Ne la mettez pas en court-circuit. Pour la mettre au rebut,  
conformez-vous à la réglementation en vigueur. Lorsque vous remplacez la  
batterie, veillez à n’utiliser que les modèles cités dans la liste de pièces  
détachées adéquate. En effet, une batterie inappropriée risque de prendre  
feu ou d’exploser.  
Akkus enthalten geringe Mengen von Nickel. Sie dürfen nicht zerlegt,  
wiederaufgeladen, kurzgeschlossen, oder Feuer oder Wasser ausgesetzt  
werden. Bei der Entsorgung die örtlichen Bestimmungen für Sondermüll  
beachten. Beim Ersetzen der Batterie nur Batterien des Typs verwenden, der  
in der Ersatzteilliste aufgeführt ist. Der Einsatz falscher Batterien kann zu  
Entzündung oder Explosion führen.  
La batteria contiene piccole quantità di nichel. Non smontarla, gettarla nel  
fuoco o nell’acqua né cortocircuitarla. Smaltirla secondo la normativa in  
vigore (DPR 915/82, successive disposizioni e disposizioni locali). Quando  
si sostituisce la batteria, utilizzare soltanto i tipi inseriti nell’appropriato  
Catalogo parti. L’impiego di una batteria non adatta potrebbe determinare  
l’incendio o l’esplosione della batteria stessa.  
Las baterías contienen pequeñas cantidades de níquel. No las desmonte, ni  
recargue, ni las eche al fuego o al agua ni las cortocircuite. Deséchelas tal  
como dispone la normativa local. Utilice sólo baterías que se encuentren en  
la lista de piezas al sustituir la batería. La utilización de una batería no  
apropiada puede provocar la ignición o explosión de la misma.  
9
 
Lenovo IdeaTab S2110A Hardware Maintenance Manual  
Safety notice 4  
DANGER  
The lithium battery can cause a fire, an explosion, or a severe burn. Do not  
recharge it, remove its polarized connector, disassemble it, heat it above  
100°C (212°F), incinerate it, or expose its cell contents to water. Dispose of  
the battery as required by local ordinances or regulations. Use only the  
battery in the appropriate parts listing. Use of an incorrect battery can result  
in ignition or explosion of the battery.  
La pile de sauvegarde contient du lithium. Elle présente des risques  
d’incendie, d’explosion ou de brûlures graves. Ne la rechargez pas, ne  
retirez pas son connecteur polarisé et ne la démontez pas. Ne l’exposez pas  
à une temperature supérieure à 100°C, ne la faites pas brûler et n’en exposez  
pas le contenu à l’eau. Mettez la pile au rebut conformément à la  
réglementation en vigueur. Une pile inappropriée risque de prendre feu ou  
d’exploser.  
Die Systembatterie ist eine Lithiumbatterie. Sie kann sich entzünden,  
explodieren oder schwere Verbrennungen hervorrufen. Batterien dieses  
Typs dürfen nicht aufgeladen, zerlegt, über 100 C erhitzt oder verbrannt  
werden. Auch darf ihr Inhalt nicht mit Wasser in Verbindung gebracht oder  
der zur richtigen Polung angebrachte Verbindungsstecker entfernt werden.  
Bei der Entsorgung die örtlichen Bestimmungen für Sondermüll beachten.  
Beim Ersetzen der Batterie nur Batterien des Typs verwenden, der in der  
Ersatzteilliste aufgeführt ist. Der Einsatz falscher Batterien kann zu  
Entzündung oder Explosion führen.  
La batteria di supporto e una batteria al litio e puo incendiarsi, esplodere o  
procurare gravi ustioni. Evitare di ricaricarla, smontarne il connettore  
polarizzato, smontarla, riscaldarla ad una temperatura superiore ai 100  
gradi centigradi, incendiarla o gettarla in acqua. Smaltirla secondo la  
normativa in vigore (DPR 915/82, successive disposizioni e disposizioni  
locali). L’impiego di una batteria non adatta potrebbe determinare  
l’incendio o l’esplosione della batteria stessa.  
La batería de repuesto es una batería de litio y puede provocar incendios,  
explosiones o quemaduras graves. No la recargue, ni quite el conector  
polarizado, ni la desmonte, ni caliente por encima de los 100°C (212°F), ni la  
incinere ni exponga el contenido de sus celdas al agua. Deséchela tal como  
dispone la normativa local.  
10  
 
Safety information  
Safety notice 5  
If the LCD breaks and the fluid from inside the LCD gets into your eyes or  
on your hands, immediately wash the affected areas with water at least for  
15 minutes. Seek medical care if any symptoms caused by the fluid are  
present after washing.  
Si le panneau d’affichage à cristaux liquides se brise et que vous recevez dans  
les yeux ou sur les mains une partie du fluide, rincez-les abondamment  
pendant au moins quinze minutes. Consultez un médecin si des symptômes  
persistent après le lavage.  
Die Leuchtstoffröhre im LCD-Bildschirm enthält Quecksilber. Bei der  
Entsorgung die örtlichen Bestimmungen für Sondermüll beachten. Der  
LCD-Bildschirm besteht aus Glas und kann zerbrechen, wenn er  
unsachgemäß behandelt wird oder der Computer auf den Boden fällt. Wenn  
der Bildschirm beschädigt ist und die darin befindliche Flüssigkeit in  
Kontakt mit Haut und Augen gerät, sollten die betroffenen Stellen  
mindestens 15 Minuten mit Wasser abgespült und bei Beschwerden  
anschließend ein Arzt aufgesucht werden.  
Nel caso che caso l’LCD si dovesse rompere ed il liquido in esso contenuto  
entrasse in contatto con gli occhi o le mani, lavare immediatamente le parti  
interessate con acqua corrente per almeno 15 minuti; poi consultare un  
medico se i sintomi dovessero permanere.  
Si la LCD se rompe y el fluido de su interior entra en contacto con sus ojos o  
sus manos, lave inmediatamente las áreas afectadas con agua durante  
15 minutos como mínimo. Obtenga atención medica si se presenta algún  
11  
 
Lenovo IdeaTab S2110A Hardware Maintenance Manual  
Safety notice 6  
DANGER  
To avoid shock, do not remove the plastic cover that protects the lower part  
of the inverter card.  
Afin d’éviter tout risque de choc électrique, ne retirez pas le cache en  
plastique protégeant la partie inférieure de la carte d’alimentation.  
Aus Sicherheitsgründen die Kunststoffabdeckung, die den unteren Teil der  
Spannungswandlerplatine umgibt, nicht entfernen.  
Per evitare scosse elettriche, non rimuovere la copertura in plastica che  
avvolge la parte inferiore della scheda invertitore.  
Para evitar descargas, no quite la cubierta de plástico que rodea la parte baja  
de la tarjeta invertida.  
Safety notice 7  
DANGER  
Though the main batteries have low voltage, a shorted or grounded battery  
can produce enough current to burn personnel or combustible materials.  
Bien que le voltage des batteries principales soit peu élevé, le court-circuit ou  
la mise à la masse d’une batterie peut produire suffisamment de courant  
pour brûler des matériaux combustibles ou causer des brûlures corporelles  
graves.  
Obwohl Hauptbatterien eine niedrige Spannung haben, können sie doch bei  
Kurzschluß oder Erdung genug Strom abgeben, um brennbare Materialien  
zu entzünden oder Verletzungen bei Personen hervorzurufen.  
Sebbene le batterie di alimentazione siano a basso voltaggio, una batteria in  
corto circuito o a massa può fornire corrente sufficiente da bruciare materiali  
combustibili o provocare ustioni ai tecnici di manutenzione.  
Aunque las baterías principales tienen un voltaje bajo, una batería  
cortocircuitada o con contacto a tierra puede producir la corriente suficiente  
como para quemar material combustible o provocar quemaduras en el  
personal.  
12  
 
Safety information  
Safety notice 8  
DANGER  
Before removing any FRU, turn off the computer, unplug all power cords  
from electrical outlets, remove the battery pack, and then disconnect any  
interconnecting cables.  
Avant de retirer une unité remplaçable en clientèle, mettez le système hors  
tension, débranchez tous les cordons d’alimentation des socles de prise de  
courant, retirez la batterie et déconnectez tous les cordons d’interface.  
Die Stromzufuhr muß abgeschaltet, alle Stromkabel aus der Steckdose  
gezogen, der Akku entfernt und alle Verbindungskabel abgenommen sein,  
bevor eine FRU entfernt wird.  
Prima di rimuovere qualsiasi FRU, spegnere il sistema, scollegare dalle prese  
elettriche tutti i cavi di alimentazione, rimuovere la batteria e poi scollegare  
i cavi di interconnessione.  
Antes de quitar una FRU, apague el sistema, desenchufe todos los cables de  
las tomas de corriente eléctrica, quite la batería y, a continuación, desconecte  
cualquier cable de conexión entre dispositivos.  
13  
 
Lenovo IdeaTab S2110A Hardware Maintenance Manual  
Laser compliance statement  
Some models of Lenovo computer are equipped from the factory with an optical  
storage device such as a CD-ROM drive or a DVD-ROM drive. Such devices are  
also sold separately as options. If one of these drives is installed, it is certified in  
the U.S. to conform to the requirements of the Department of Health and Human  
Services 21 Code of Federal Regulations (DHHS 21 CFR) Subchapter J for Class  
1 laser products. Elsewhere, the drive is certified to conform to the requirements  
of the International Electrotechnical Commission (IEC) 825 and CENELEC EN 60  
825 for Class 1 laser products.  
If a CD-ROM drive, a DVD-ROM drive, or another laser device is installed, note  
the following:  
CAUTION  
Use of controls or adjustments or performance of procedures other than  
those specified herein might result in hazardous radiation exposure.  
O uso de controles, ajustes ou desempenho de procedimentos diferentes  
daqueles aqui especificados pode resultar em perigosa exposição à radiação.  
Pour éviter tout risque d’exposition au rayon laser, respectez les consignes  
de réglage et d’utilisation des commandes, ainsi que les procédures décrites.  
Werden Steuer- und Einstellelemente anders als hier festgesetzt verwendet,  
kann gefährliche Laserstrahlung auftreten.  
L’utilizzo di controlli, regolazioni o l’esecuzione di procedure diverse da  
quelle specificate possono provocare l’esposizione a.  
El uso de controles o ajustes o la ejecución de procedimientos distintos de los  
aquí especificados puede provocar la exposición a radiaciones peligrosas.  
Opening the CD-ROM drive, the DVD-ROM drive, or any other optical storage  
device could result in exposure to hazardous laser radiation. There are no  
serviceable parts inside those drives. Do not open.  
14  
 
 
Safety information  
A CD-ROM drive, a DVD-ROM drive, or any other storage device installed may  
contain an embedded Class 3A or Class 3B laser diode. Note the following:  
DANGER  
Emits visible and invisible laser radiation when open. Do not stare into the  
beam, do not view directly with optical instruments, and avoid direct  
exposure to the beam.  
Radiação por raio laser ao abrir. Não olhe fixo no feixe de luz, não olhe  
diretamente por meio de instrumentos óticos e evite exposição direta com o  
feixe de luz.  
Rayonnement laser si carter ouvert. Évitez de fixer le faisceau, de le regarder  
directement avec des instruments optiques, ou de vous exposer au rayon.  
Laserstrahlung bei geöffnetem Gerät. Nicht direkt oder über optische  
Instrumente in den Laserstrahl sehen und den Strahlungsbereich meiden.  
Kinyitáskor lézersugár ! Ne nézzen bele se szabad szemmel, se optikai  
eszközökkel. Kerülje a sugárnyalábbal való érintkezést!  
Aprendo l’unità vengono emesse radiazioni laser. Non fissare il fascio, non  
guardarlo direttamente con strumenti ottici e evitare l’esposizione diretta al  
fascio.  
Radiación láser al abrir. No mire fijamente ni examine con instrumental  
óptico el haz de luz. Evite la exposición directa al haz.  
15  
 
Lenovo IdeaTab S2110A Hardware Maintenance Manual  
Important service information  
This chapter presents the following important service information:  
Important:  
BIOS and device driver fixes are customer-installable. The BIOS and device  
drivers are posted on the customer support site:  
Strategy for replacing FRUs  
Before replacing parts:  
Make sure that all software fixes, drivers, and BIOS downloads are installed  
before replacing any FRUs listed in this manual.  
After a system board is replaced, ensure that the latest BIOS is loaded to the  
system board before completing the service action.  
To download software fixes, drivers, and BIOS, follow the steps below:  
2. Enter a serial number or select a product or use Lenovo smart downloading.  
3. Select the BIOS/Driver/Applications and download.  
4. Follow the directions on the screen and install the necessary software.  
16  
 
     
Important service information  
Use the following strategy to prevent unnecessary expense for replacing and  
servicing FRUs:  
• If you are instructed to replace an FRU, but the replacement does not solve  
the problem, reinstall the original FRU before you continue.  
• Some computers have both a processor board and a system board. If you are  
instructed to replace either of them, and replacing one of them does not solve  
the problem, reinstall that board, and then replace the other one.  
• If an adapter or a device consists of more than one FRU, any of the FRUs may  
be the cause of the error. Before replacing the adapter or device, remove the  
FRUs one by one to see if the symptoms change. Replace only the FRU that  
changed the symptoms.  
Attention: The setup configuration on the computer you are servicing may have  
been customized. Running Automatic Configuration may alter the settings. Note  
the current configuration settings (using the View Configuration option); then,  
when service has been completed, verify that those settings remain in effect.  
Important notice for replacing a system board  
Some components mounted on a system board are very sensitive. Improper  
handling can cause damage to those components, and may cause a system  
malfunction.  
Attention: When handling a system board:  
• Do not drop the system board or apply any excessive force to it.  
Avoid rough handling of any kind.  
Avoid bending the system board and hard pushing to prevent cracking at  
each BGA (Ball Grid Array) chipset.  
17  
 
 
Lenovo IdeaTab S2110A Hardware Maintenance Manual  
Important information about replacing RoHS compliant FRUs  
RoHS, The Restriction of Hazardous Substances in Electrical and  
Electronic Equipment Directive (2002/95/EC) is a European Union legal  
requirement affecting the global electronics industry. RoHS requirements  
must be implemented on Lenovo products placed on the market after June  
2006. Products on the market before June 2006 are not required to have  
RoHS compliant parts. If the original FRU parts are non-compliant,  
replacement parts can also be non-compliant. In all cases if the original  
FRU parts are RoHS compliant, the replacement part must also be RoHS  
compliant.  
Note: RoHS and non-RoHS FRU part numbers with the same fit and function are  
identified with unique FRU part numbers.  
Lenovo plans to transit to RoHS compliance well before the implementation date  
and expects its suppliers to be ready to support Lenovo’s requirements and  
schedule in the EU. Products sold in 2005 and 2006 will contain some RoHS  
compliant FRUs. The following statement pertains to these products and any  
product Lenovo produces containing RoHS compliant FRUs.  
RoHS compliant FRUs have unique FRU part numbers. Before or after the RoHS  
implementation date, failed RoHS compliant parts must always be replaced with  
RoHS compliant ones, so only the FRUs identified as compliant in the system  
HMM or direct substitutions for those FRUs may be used.  
Products marketed before June 2006 Products marketed after June 2006  
Current or  
original part  
Replacement  
FRU  
Current or  
original part  
Replacement  
FRU  
Non-RoHS  
Non-RoHS  
Non-RoHS  
RoHS  
Can be Non-RoHS  
Can be RoHS  
Must be RoHS  
Must be RoHS  
Can sub to RoHS  
Must be RoHS  
Note: A direct substitution is a part with a different FRU part number that is  
automatically shipped by the distribution center at the time of the order.  
18  
 
 
General checkout  
General checkout  
This chapter presents the following information:  
Before you go to the checkout, make sure to read the following important notes:  
Important notes:  
Only certified trained personnel can service the computer.  
Before replacing any FRU, read the entire page on removing and  
replacing FRUs.  
When you replace FRUs, use new nylon-coated screws.  
Be extremely careful during such write operations as copying,  
saving, or formatting. Drives in the computer that you are servicing  
sequence might have been altered. If you select an incorrect drive, data  
or programs might be overwritten.  
Replace an FRU only with another FRU of the correct model. When  
you replace an FRU, make sure that the machine model and the FRU part  
number are correct by referring to the FRU parts list.  
An FRU should not be replaced just because of a single,  
unreproducible failure. Single failures can occur for a variety of reasons  
that have nothing to do with a hardware defect, such as cosmic radiation,  
electrostatic discharge, or software errors. Consider replacing an FRU  
only when a problem recurs. If you suspect that an FRU is defective,  
clear the error logs and run the test again. If the error does not recur, do  
not replace the FRU.  
Be careful not to replace a nondefective FRU.  
19  
 
 
Lenovo IdeaTab S2110A Hardware Maintenance Manual  
What to do first  
When you do return an FRU, you must include the following information in the  
parts exchange form or parts return form that you attach to it:  
1. Name and phone number of servicer  
2. Date of service  
3. Date on which the machine failed  
4. Date of purchase  
5. Procedure index and page number in which the failing FRU was detected  
6. Failing FRU name and part number  
7. Machine type, model number, and serial number  
8. Customer’s name and address  
Note for warranty: During the warranty period, the customer may be  
responsible for repair costs if the computer damage was caused by misuse,  
accident, modification, unsuitable physical or operating environment, or  
improper maintenance by the customer.  
The following is a list of some common items that are not covered under  
warranty and some symptoms that might indicate that the system was subjected  
to stress beyond normal use.  
Before checking problems with the computer, determine whether the damage is  
covered under the warranty by referring to the following list:  
The following are not covered under warranty:  
• LCD panel cracked from the application of excessive force or from being  
dropped  
• Scratched (cosmetic) parts  
• Distortion, deformation, or discoloration of the cosmetic parts  
• Plastic parts, latches, pins, or connectors that have been cracked or broken by  
excessive force  
• Damage caused by liquid spilled into the system  
• Damage caused by the improper insertion of a PC Card or the installation of  
an incompatible card  
• Improper disk insertion or use of an optical drive  
• Diskette drive damage caused by pressure on the diskette drive cover, foreign  
material in the drive, or the insertion of a diskette with multiple labels  
• Damaged or bent diskette eject button  
• Fuses blown by attachment of a nonsupported device  
• Forgotten computer password (making the computer unusable)  
• Sticky keys caused by spilling a liquid onto the keyboard  
• Use of an incorrect AC adapter on laptop products  
The following symptoms might indicate damage caused by nonwarranted  
activities:  
• Missing parts might be a symptom of unauthorized service or modification.  
• If the spindle of a hard disk drive becomes noisy, it may have been subjected  
to excessive force, or dropped.  
20  
 
 
General checkout  
Power system checkout  
To verify a symptom, follow the steps below:  
1. Turn off the computer.  
2. Remove the battery pack.  
3. Connect the AC adapter.  
4. Make sure that power is supplied when you turn on the computer.  
5. Turn off the computer.  
6. Disconnect the AC adapter and install the charged battery pack.  
7. Make sure that the battery pack supplies power when you turn on the  
computer.  
If you suspect a power problem, see the appropriate one of the following power  
supply checkouts:  
Checking the AC adapter  
You are here because the computer fails only when the AC adapter is used.  
• If the power-on indicator does not turn on, check the power cord of the AC  
adapter for correct continuity and installation.  
• If the computer does not charge during operation, go to “Checking  
operational charging”.  
To check the AC adapter, follow the steps below:  
1. Unplug the AC adapter cable from the computer.  
2. Measure the output voltage at the plug of the AC adapter cable. See the  
following figure:  
Pin  
1
Voltage (V DC)  
+20  
0
2
2
1
Note: Output voltage for the AC adapter pin No. 2 may differ from the one you  
are servicing.  
3. If the voltage is not correct, replace the AC adapter.  
4. If the voltage is acceptable, do the following:  
• Replace the system board.  
• If the problem continues, go to “Lenovo IdeaTab S2110A” on page 24.  
Note: Noise from the AC adapter does not always indicate a defect.  
Checking operational charging  
To check whether the battery charges properly during operation, use a  
discharged battery pack or a battery pack that has less than 50% of the total  
power remaining when installed in the computer.  
21  
 
     
Lenovo IdeaTab S2110A Hardware Maintenance Manual  
Perform operational charging. If the battery status indicator or icon does not  
light on, remove the battery pack and let it return to room temperature. Reinstall  
the battery pack. If the charge indicator or icon is still off, replace the battery  
pack.  
If the charge indicator still does not light on, replace the system board. Then  
reinstall the battery pack. If it is still not charged, go to the next section.  
Checking the battery pack  
Battery charging does not start until the Power Meter shows that less than 95%  
of the total power remains; under this condition the battery pack can charge to  
100% of its capacity. This protects the battery pack from being overcharged or  
from having a shortened life.  
To check your battery, move your cursor to the Power Meter icon in the icon tray  
®
of the Windows taskbar and wait for a moment (but do not click it), and the  
percentage of battery power remaining is displayed. To get detailed information  
about the battery, double-click the Power Meter icon.  
Note: If the battery pack becomes hot, it may not be able to be charged. Remove  
it from the computer and leave it at room temperature for a while. After it cools  
down, reinstall and recharge it.  
To check the battery pack, follow the steps below:  
1. Turn off the computer.  
2. Remove the battery pack and measure the voltage between battery terminals  
1 (+) and 7 (-). See the following figure:  
Terminal  
Voltage (V DC)  
+0 to +14  
1
7
7(-)  
6(-)  
5
Ground (-)  
4
3
2(+)  
1(+)  
3. If the voltage is less than +11.0 V DC, the battery pack has been discharged.  
Note: Recharging will be continued for at least 3 hours, even though the  
indicator does not light on.  
If the voltage is still less than +11.0 V DC after recharging, replace the battery.  
4. If the voltage is more than +11.0 V DC, measure the resistance between  
battery terminals 5 and 7. The resistance must be 4 to 30 KΩ.  
If the resistance is not correct, replace the battery pack. If the resistance is  
correct, replace the system board.  
22  
 
 
Related service information  
Related service information  
This chapter presents the following information:  
Passwords  
With this option, you can decide whether or not your chosen password will be  
visible as you input it. If the checkbox is checked, then the password will be  
visible. If it is unchecked, then your password will only be displayed as **** as  
you input it, thereby keeping your password more secure.  
Power settings  
With these settings, you can set “Enable Power Efficiency”, “Enable energy-  
saving”, “On energy-saving” and “Energy-saving settings”.  
Turning Screen Backlight On/Off  
Turning Screen Backlight On  
In the standby mode, you can tap the "Power/Wake up" button on the top of the  
IdeaTab to wake the screen up. The device's screen will then light up, indicating  
that the backlight has been turned on.  
Turning Screen Backlight Off  
If your IdeaTab is powered on and you do not use it temporarily, you can tap the  
"Power/Wake up" button on its top to turn off the screen backlight. Your  
IdeaTab will enter the standby mode to save power.  
23  
 
       
Lenovo IdeaTab S2110A Hardware Maintenance Manual  
Lenovo IdeaTab S2110A  
This chapter presents the following product-specific service references and  
product-specific parts information:  
Specifications  
The following table lists the specifications of the Lenovo IdeaTab S2110A:  
Table 1. Specifications  
Feature  
Form Factor  
Size  
Description  
• 259.77mm x 177.97mm x 8.69mm *  
• 590g *  
Weight  
System  
Platform  
• Qualcomm MSM8060A/MSM8260A/  
MSM-8660A/MSM-8960  
Memory  
• 1G LP-DDR2  
LCD  
• 10.1” HD LED (1280 x 800 Widescreen view)  
• 1.3M on front/5.0M on back  
• 2-cell Li-polymer battery  
Integrated Camera  
Battery  
Operating System  
• Android  
Ports  
• 3.5mm Combo Audio jack  
• Dock connector (compatible with Micro USB)  
• Micro SD card slot  
• Micro HDMI (Type D) jack  
• SIM card slot (On select models)  
Communication  
Others  
• WLAN  
• Bluetooth  
• 3G WWAN (On select models)  
• Multi-touch supported  
• Built-in microphone  
• Stereophonic loudspeakers  
• Compass  
• Gyroscope  
24  
 
   
Lenovo IdeaTab S2110A  
Table 1. Specifications (continued)  
Feature  
MODEM slot  
Audio  
Description  
• N/A  
• HD Audio 5.1 channel supported via HDMI output  
Tan 802.11 b/g/n & combo  
• Atheros b/g/n  
WLAN  
3G  
• On select models  
Bluetooth  
Camera  
Battery  
AC adapter  
• BT2.1 + EDR  
• 1.3M HD (Front) + 5M (Back)  
• 2-cell Li-polymer  
• 5V, 10W/black  
Pre-installed  
• Android  
operating system  
* Subject to actual measurement.  
25  
 
Lenovo IdeaTab S2110A Hardware Maintenance Manual  
FRU replacement notices  
This section presents notices related to removing and replacing parts. Read this  
section carefully before replacing any FRU.  
Screw notices  
Loose screws can cause a reliability problem. In the Lenovo computer, this  
problem is addressed with special nylon-coated screws that have the following  
characteristics:  
• They maintain tight connections.  
• They do not easily come loose, even with shock or vibration.  
• They are harder to tighten.  
• Each one should be used only once.  
Do the following when you service this machine:  
• Keep the screw kit in your tool bag.  
• Always use new screws.  
• Use a torque screwdriver if you have one.  
Tighten screws as follows:  
Plastic to plastic  
Turn an additional 90° after the screw head touches the surface of the plastic  
part:  
more than 90°  
(Cross-section)  
Logic card to plastic  
Turn an additional 180° after the screw head touches the surface of the logic  
card:  
more than 180°  
(Cross-section)  
Torque driver  
If you have a torque screwdriver , refer to the “Torque” column for each step.  
• Make sure that you use the correct screws. If you have a torque screwdriver,  
tighten all screws firmly to the torque shown in the table. Never use a screw  
that you removed. Use a new one. Make sure that all screws are  
tightened firmly.  
• Ensure torque screwdrivers are calibrated correctly following country  
specifications.  
26  
 
   
Lenovo IdeaTab S2110A  
Removing and replacing an FRU  
This section presents exploded figures with the instructions to indicate how to  
remove and replace the FRU. Make sure to observe the following general rules:  
1. Do not attempt to service any computer unless you have been trained and  
certified. An untrained person runs the risk of damaging parts.  
2. Before replacing any FRU, review “FRU replacement notices” on page 26.  
3. Begin by removing any FRUs that have to be removed before the failing FRU.  
Any of such FRUs are listed at the top of the page. Remove them in the order  
in which they are listed.  
4. Follow the correct sequence in the steps to remove the FRU, as given in the  
figures by the numbers in square callouts.  
5. When turning a screw to replace an FRU, turn it in the direction as given by  
the arrow in the figure.  
6. When removing the FRU, move it in the direction as given by the arrow in the  
figure.  
7. To put the new FRU in place, reverse the removal procedures and follow any  
of the notes that pertain to replacement. For information about connecting  
and arranging internal cables, see “Locations” on page 35.  
8. When replacing an FRU, use the correct screw as shown in the procedures.  
DANGER  
Before removing any FRU, turn off the computer, unplug all power cords  
from electrical outlets, remove the battery pack, and then disconnect any of  
the interconnecting cables.  
Attention: After replacing an FRU, do not turn on the computer until you have  
made sure that all screws, springs, and other small parts are in place and none  
are loose inside the computer. Verify this by shaking the computer gently and  
listening for rattling sounds. Metallic parts or metal flakes can cause electrical  
short circuits.  
Attention: The system board is sensitive to, and can be damaged by, electrostatic  
discharge. Before touching it, establish personal grounding by touching a  
ground point with one hand or using an electrostatic discharge (ESD) strap  
(P/N 6405959) to remove potential shock reasons.  
27  
 
 
Lenovo IdeaTab S2110A Hardware Maintenance Manual  
1010 Battery pack  
DANGER  
Only use the battery specified in the parts list for your IdeaTab. Any other  
battery could ignite or explode.  
Figure 1. Removal steps of battery pack  
Pull out the SIM card slot cover with a fingertip in the direction shown by the  
arrow  
.
a
1
Open the back cover along the device frame with a flat blade in the direction  
shown by arrows  
. Lift the back cover in the direction shown by the arrow  
b
.
c
2
2
2
3
2
Disconnect the battery connector  
, then remove the battery by holding the  
a
right edge of the battery pack in the direction shown by the arrow.  
1
28  
 
 
Lenovo IdeaTab S2110A  
1020 SIM card/Micro SD card  
Figure 2. Removal steps of SIM card/Micro SD card  
Pull out the SIM card slot cover the card slot cover in the direction shown by  
arrow  
.
a
1
Remove the SIM card or Micro card in the direction shown by arrows  
.
b c  
3
2
29  
 
 
Lenovo IdeaTab S2110A Hardware Maintenance Manual  
1030 Back camera  
For access, remove these FRUs in order:  
Figure 3. Removal steps of back camera  
Detach the back camera connector  
and remove it.  
a
1
30  
 
 
Lenovo IdeaTab S2110A  
1040 System board  
Important notices for handling the system board:  
When handling the system board, bear the following in mind.  
• Be careful not to drop the system board on a bench top that has a hard  
surface, such as metal, wood, or composite.  
• Avoid rough handling of any kind.  
• In the whole process, make sure not to drop or stack the system board.  
• If you put a system board down, make sure to put it only on a padded  
surface such as an ESD mat or conductive corrugated material.  
For access, remove these FRUs in order:  
31  
 
 
Lenovo IdeaTab S2110A Hardware Maintenance Manual  
Figure 4. Removal steps of system board  
Detach Switch board FPC connector  
.
a
1
1
Remove the three screws  
.
b
2
2
2
Detach Volume FFC connector  
, LVDS cable connector  
, Touch FPC  
c
d
connector  
, and Speaker connector  
.
e
f
3
4
6
5
32  
 
Lenovo IdeaTab S2110A  
Figure 4. Removal steps of system board  
Lift the system board in the direction shown by arrow  
. Disconnect the  
g
Vibrator motor connector  
. Then remove the system board.  
h
7
8
Step Screw (quantity)  
Color Torque  
M2X2.3L, flat-head, nylok-coated (4)  
Black  
1.0 ~ 1.5 kgfcm  
a
33  
 
Lenovo IdeaTab S2110A Hardware Maintenance Manual  
1050 LCD  
For access, remove these FRUs in order:  
Figure 5. Removal steps of all parts  
Remove the eleven screws  
.
a
1
1
1
1
1
1
1
1
1
1
1
Remove the left speaker module  
and volume board  
. Be sure to  
b
g
disconnect the connector at the back. Peel off the right speaker module  
.
c
Remove the Dock hooks  
and  
, then switch board  
.
d
f
e
2
3
7
4
5
6
Step Screw (quantity)  
Color Torque  
Black 1.0 ~ 1.5 kgfcm  
M2X2.3L, flat-head, nylok-coated (6)  
a
34  
 
 
Lenovo IdeaTab S2110A  
Locations  
Front view  
Front camera  
a
1
35  
 
   
Lenovo IdeaTab S2110A Hardware Maintenance Manual  
Right-side view  
Speaker  
a
Volume +/-  
b
1
2
Top view  
Power button  
a
1
36  
 
   
Lenovo IdeaTab S2110A  
Back view  
Flash  
a
Back camera  
b
1
2
Left-side view  
Speaker  
a
b
c
d
Combo audio jack  
Micro HDMI port  
Micro SD card slot/SIM card slot (On select models)  
1
2
3
4
37  
 
   
Lenovo IdeaTab S2110A Hardware Maintenance Manual  
Parts list  
This section presents the following service parts:  
Notes:  
• Each FRU is available for all types or models, unless specific types or  
models are specified.  
38  
 
 
Lenovo IdeaTab S2110A  
Overall  
1
2
3
4
6
5
7
8
10  
9
11  
12  
39  
 
 
Lenovo IdeaTab S2110A Hardware Maintenance Manual  
Table 1. Parts list—Overall  
No. FRU  
FRU no.  
CRU ID  
1
2
3
4
5
6
7
8
SYSTEM BOARD  
VOLUME BOARD  
SWITCH BOARD  
90000609  
90000676  
90000677  
90000672  
90000673  
90201530  
90201513  
90201517  
90201526  
90201525  
31052540  
90400058  
N
N
N
N
N
N
N
N
N
N
N
N
SPEAKER MODULE LEFT  
SPEAKER MODULE RIGHT  
VOLUME BUTTON  
BACK CAMERA  
SWITCH BOARD FPC  
DOCK HOOK LEFT  
DOCK HOOK RIGHT  
Battery  
9
10  
11  
12  
LCD MODULE  
40  
 
Lenovo IdeaTab S2110A  
AC adapters  
Table 2. Parts list—3-pin AC adapters  
FRU  
P/N  
CRU ID  
S2 18AW AA 12V1.5A Adapter  
36200114  
N
USB Cable  
Table 3. Parts list—USB Cable  
FRU  
P/N  
CRU ID  
USB CABLE  
90201534  
N
SD Card  
SD/SIM Card Slot is available to support SD card.  
41  
 
     
Lenovo IdeaTab S2110A Hardware Maintenance Manual  
Trademarks  
Legend, Lenovo, Lenovo 联想 , 联想 , IdeaPad, IdeaTab and other Lenovo logos  
are trademarks of Lenovo in Mainland China and/or other countries/territories.  
Other product names, service names, trade names or brands are trademarks of  
their respective owners.  
Copyright © 2011 Lenovo, all rights reserved.  
42  
 
 

KWC Plumbing Product 28243226000 User Manual
Lantronix Network Card 900 588 User Manual
Legacy Car Audio Car Video System LSC7 User Manual
Lexicon Musical Instrument Recording Studio User Manual
Lincoln Automobile 2010 Town Car User Manual
Magnavox VCR VRB411AT User Manual
Makita Drill 6402 DP4700 User Manual
Manley Labs Stereo Amplifier STUDIO STANDARD 350 WATT MONOBLOCK AMPLIFIER User Manual
Melissa Mixer 646 050 User Manual
Memorex Cordless Telephone MPH2430 User Manual