Lightolier Indoor Furnishings 1084CD User Manual

INSTRUCTION SHEET NO.  
READ AND UNDERSTAND THESE INSTRUCTIONS BEFORE INSTALLING FIXTURE  
This fixture is intended for installation in accordance with the National Electrical Code and local regulations. To  
assure full compliance with local codes and regulations, check with your local electrical inspector before  
installation. To prevent electric shock, turn off electricity at fuse box before proceeding.  
IS:1184  
Retain these instructions for maintenance reference.  
Page 1 of 1  
B1104  
INSTALLATION PROCEDURE FOR: 1184WH, 1184CD, 1084WH, 1084CD, 2084WH, 2084CD  
1184WH and 1184CD for use with 1104ICX, 1103R, 1100IC, 1100AICM and 1102P1 only.  
1084WH and 1084CD for use with 1004ICX, 1003R, 1000IC, 1000AICM and 1002P1 only.  
2084WH and 2084CD for use with 2000IC, 2000AIC, 2003R and 2002P1 only.  
CAUTION: (RISK OF FIRE) FOR NON-IC RATED INSTALLATIONS, DO NOT INSTALL INSULATION ABOVE  
OR WITHIN 3 INCHES OF ANY PART OF FIXTURE.  
CAUTION: USE ONLY REFLECTOR TRIMS PROVIDED BY LIGHTOLIER. USE OF OTHER MANUFACTURER’S REFLECTOR  
TRIMS MAY VOID THE UNDERWRITERS LABORATORIES LISTING AND COULD CONSTITUTE A FIRE HAZARD.  
CAUTION: BEFORE INSTALLING REFLECTOR TO FRAME-IN-KIT, READ MARKINGS IN REFLECTOR AND IN SOCKET CUP  
OF FRAME-IN-KIT TO DETERMINE LAMP WATTAGE AND TYPE APPLICABLE FOR YOUR INSTALLATION.  
1 FRAME-IN KIT INSTALLATION: See Frame-In Kit Instruction Sheet for installation procedure.  
2 GASKET INSTALLATION:  
A. Align open side of gasket towards socket cup (figure A).  
B. Pinch gasket and insert both edges under the reflector spring clip. (figure B).  
C. Push center of gasket back into socket cup until inner diameter fits over the lamp socket  
and smaller thru hole in gasket sits on top of socket (figure C).  
Figure A  
Figure C  
Figure B  
CAUTION – DO NOT STRETCH SMALL HOLE OF GASKET OVER LAMP SOCKET.  
THE GASKET MUST SIT ON TOP OF SOCKET TO PROVIDE SEAL TO LAMP.  
3 ROTATE ROTO-CLIPS:  
Rotate (4) ROTO-CLIPS so that the short legs extend inwardly toward center  
opening (figure D).  
Note: The short leg of the ROTO-CLIP has no return on top.  
Figure D  
4 SNAP ON:  
Insert gasketed socket cup into neck of reflector trim making sure spring clips of  
socket cup snap into slots of reflector (figure E). If reflector trim has 2 sets of slots,  
the upper slot is used for IC frame-in kits, the lower slot for non-IC frame-in kits.  
Note: At no time should the lamp extend outside the reflector trim.  
Figure E  
Figure F  
5 PUSH UP:  
Align Reflector Trim so that ROTO-CLIPS will not interfere with socket cup spring  
clips and push reflector trim straight up into fixture housing until it is tight against  
ceiling (figure F).  
Note: To remove reflector trim, turn reflector trim counterclockwise while pulling  
downward. Once trim is out of the ceiling, squeeze reflector spring clips until the  
trim disengages from socket cup. (figure G).  
Replacement Gasket Available: Lightolier Catalog No. LFG356  
Figure G  
A
COMPANY  
631 Airport Road, Fall River, MA 02720  
 

KWC Indoor Furnishings 20240060000 User Manual
LaCie Computer Drive Databank User Manual
Lenovo Personal Computer Q700 User Manual
Lenoxx Electronics CD Player CD625 User Manual
Lincoln Electric Welding Consumables CAN F10 C User Manual
Marantz Blu ray Player UD8004 User Manual
Martin Audio Speaker CS265 User Manual
Memorex Stereo System MKS5622 User Manual
Metabo Welding System MIG MAG 301 E User Manual
Metra Electronics Car Stereo System 99 7013 User Manual