Lumex Syatems Marine Instruments AQ1000 User Manual

AQ1000 / AQ2000  
ALTERNATING PRESSURE  
BUBBLE PAD AND PUMP SYSTEM  
USER MANUAL  
Important: Do not operate the Mattress System  
without first reading and understanding this manual!  
Save this manual for future use.  
The latest version of this manual can be found online  
AQ1000-INS-LAB-RevD13  
 
INTRODUCTION  
Use this manual for setup and operation of the Lumex  
AQ1000 / AQ2000 Alternating Pressure Pad and Pump  
System. Read all instructions before using the pad and  
pump system. Save this manual for future reference.  
INTENDED USE OF THIS DEVICE  
The intended use of the Alternating Pressure Pad  
and Pump System, in either a homecare or long-term  
care setting, is the treatment of pressure ulcers while  
optimizing user comfort, and pain management as  
prescribed by a physician.  
Contraindication  
WARNING: DO NOT use this product in the presence of  
flammable anesthesia. There is a possible fire hazard  
when this product is used with certain oxygen delivery  
equipment.  
1
Use nasal cannula, face mask, or /2 length oxygen tent  
to deliver oxygen in the presence of this product.  
DO NOT use a full length oxygen tent that extends past  
the top surface of the mattress with this product.  
IMPORTANT SAFETY PRECAUTIONS  
The safety statements presented in this chapter refer  
to the basic safety information that should be observed  
by those using the Alternating Pressure Pad and Pump  
System. There are additional safety statements in other  
chapters or sections, which may be the same as or similar  
to the following, or specific to the operations.  
DANGER: Indicates an imminent hazard situation that, if  
not avoided, will result in death or serious injury.  
WARNING: Indicates a potential hazard situation or  
unsafe practice that, if not avoided, could result in  
death or serious injury.  
AQ1000-INS-LAB-RevD13  
3
 
CAUTION: Indicates a potential hazard or unsafe  
practice that, if not avoided, could result in minor or  
moderate personal injury.  
s NOTICE: Indicates a potential hazard or unsafe practice  
that, if not avoided, could result in product or property  
damage.  
Info: Provides application recommendations or other useful  
information to ensure that you get the most from your  
product.  
DANGER  
To reduce the risk of electrocution:  
DANGER: Always unplug this product immediately after  
using.  
DANGER: Do not use this product while bathing.  
DANGER: Do not place or store this product where it  
can fall or be pulled into a tub or sink.  
DANGER: Do not place this product in or drop into  
water or other liquid.  
DANGER: Do not reach for a product that has fallen into  
water. Unplug it immediately.  
WARNING  
To reduce the risk of burns, electrocution, fire,  
or personal injury:  
WARNING: Do not leave this product unattended when  
plugged in.  
WARNING: Always use close supervision when this  
product is used by, on, or near children or those who  
require close supervision.  
WARNING: Use this product only as intended and  
described in this manual. Do not use attachments or  
accessories not recommended by GF Health Products,  
Inc..  
4
AQ1000-INS-LAB-RevD13  
 
WARNING: Never operate this product if  
a) it has a damaged cord or plug.  
b) it is not working properly.  
c) it has been dropped or damaged.  
d) it has been dropped into water.  
Return the product to your Graham-Field authorized  
distributor.  
WARNING: Keep the cord away from heated surfaces.  
WARNING: Never block the air openings of this product  
or place it on a soft surface, such as a bed or couch,  
where the openings may be blocked. Keep the air  
opening free of lint, hair, and other similar particles.  
WARNING: Never drop or insert any object into any  
opening or hose.  
WARNING: Connect this product only to a properly  
grounded power outlet.  
WARNING: Maximum patient weight capacity for this  
product is 275 lb (125 kg), EVENLY DISTRIBUTED.  
WARNING: Notice for California Customers- California  
Proposition 65 WARNING: This product contains a  
chemical known to the State of California to cause  
cancer and reproductive or developmental harm.  
NOTICE  
s NOTICE: The pump can be used only with the  
accompanying bubble pad. Do not use it for any other  
purpose.  
AQ1000-INS-LAB-RevD13  
5
 
EQUIPMENT SYMBOLS  
Attention! Consult accompanying documents (this manual)  
“BF”symbol: Indicates that this product is in accordance with the  
degree of protection against electric shock for type BF equipment  
Grounding terminal  
Class II (for UL only)  
Disposal of Electrical & Electronic Equipment (WEEE):  
Do not treat this product as household waste. For more detailed  
information with regard to returning and recycling this product,  
please consult your local city office, household waste disposal  
service, or Graham-Field authorized distributor.  
The system has been tested and successfully approved with the following  
standards:  
U.S.  
UL 1431  
Europe  
EN 60601-1, EN 60601-1-2, EN 55011 Class B,  
EN 61000-3-2, EN 61000-3-3, IEC 801-2, IEC 801-3,  
IEC 801-4, IEC 801-5  
6
AQ1000-INS-LAB-RevD13  
 
PRODUCT DESCRIPTION  
BUBBLE PAD AND PUMP SYSTEM  
air tubes  
bubble pad  
pump  
bubble pad and pump system  
PUMP  
front panel  
air tube connectors  
wire  
hangers  
fuses  
(220V only)  
pump (AQ2000 shown)  
AQ1000-INS-LAB-RevD13  
7
 
FRONT PANEL  
AQ1000  
ON/OFF switch  
air tube connectors  
AQ1000 pump front panel  
AQ2000  
ON/OFF  
switch  
pressure  
control dial  
AQ2000 pump front panel  
Front panel pressure control dial (AQ2000 only): The  
pressure control dial controls the air pressure output. To  
increase pressure, turn the dial clockwise. To decrease  
pressure, turn the dial counter-clockwise.  
8
AQ1000-INS-LAB-RevD13  
 
INSTALLATION  
UNPACKING  
1. Before unpacking, check for obvious damage to the  
carton or its contents. If damage is evident, please  
notify the carrier and your Graham-Field authorized  
distributor.  
2. Remove all loose packing from the carton.  
3. Carefully remove all components from the carton.  
4. Inspect all components. If damage is evident, please  
notify the carrier and your Graham-Field authorized  
distributor.  
PUMP AND BUBBLE PAD INSTALLATION  
1. Remove all sheets, blankets, and pillows from the bed.  
2. Place the bubble pad on the bed mattress with the  
tubing at the patient's feet.  
wire hanger  
foot end  
bubble pad  
mattress  
pump  
(AQ2000 shown)  
installation  
3. Fold open the wire hangers on the back of the pump as  
shown above.  
4. Use the hangers to hang the pump on the bed's foot end,  
as shown above; adjust the hangers to place the pump  
in the most upright position (or place the pump on a flat  
surface easily accessible to the caregiver and/or doctor).  
s NOTICE: Place the device in a position where the  
caregiver and/or doctor can access it easily.  
AQ1000-INS-LAB-RevD13  
9
 
5. Connect one end of the air tubes to the bubble pad:  
slide the ends of the air tubes over the connectors on  
the top of the foot end of the bubble pad.  
6. Connect the other end of the air tubes to the pump  
connectors; ensure that the ends of the air tubes are  
firmly fitted over the bubble pad and pump connectors  
before continuing.  
s NOTICE: Ensure that the air tubes are not kinked or  
tucked under the bubble pad or mattress.  
WARNING: Locate all cords so that they will not be  
stepped on, tripped over, or otherwise subjected to  
damage or stress.  
WARNING: Do not use a household extension cord if  
the electrical cord does not reach the power outlet. Use  
of an improper extension cord could result in fire and  
electric shock. If an extension cord must be used, use  
a three conductor cord with ground, properly wired,  
in good electrical condition, and keep it as short as  
possible.  
WARNING: This device—which MUST be grounded—is  
equipped with a cord that has a grounding wire with  
a grounding plug. The plug must be plugged into an  
outlet that is properly installed and grounded.  
WARNING: Ensure that the local power voltage is  
appropriate for the pump unit.  
7. Plug the power cord into a properly grounded electrical  
outlet.  
10  
AQ1000-INS-LAB-RevD13  
 
OPERATION  
1. Turn the ON/OFF switch to the ON position. The pump  
will begin to deliver air into the bubble pad.  
2. Replace all sheets, blankets, and pillows on the bed.  
Info: if the pressure level seems low, check for any leakage  
in the air tubes or bubble pad. Replace any damaged tubes. If  
necessary, contact your Graham-Field authorized distributor  
for repair or replacement.  
AQ2000 ONLY: PRESSURE ADJUSTMENT  
Adjust the pressure control dial for comfort.  
Info: For maximum effectiveness, patient should sink into  
bubble pad to reduce pressure points. Ensure that patient  
does not bottom out.  
QUICK DISCONNECT  
Pull the power plug from the wall connector to disconnect  
the device quickly.  
CPR FUNCTION  
If CPR must be performed on the patient while the bubble  
pad is in use, to immediately deflate the bubble pad, pull  
the air tubes off the bubble pad or pump connectors.  
AQ1000-INS-LAB-RevD13  
11  
 
MAINTENANCE  
CLEANING  
Perform the following cleaning procedures before use and  
as necessary thereafter.  
Pump  
Wipe the pump with a clean, damp cloth and mild  
detergent, and keep it away from dust. Air dry.  
s NOTICE: Do not use phenolic products or corrosive or  
powdered cleansers to clean the pump.  
s NOTICE: Do not immerse or soak the pump.  
Bubble pad  
Wipe the bubble pad with a clean, damp cloth and mild  
detergent. The bubble pad may also be cleaned using a  
10% solution of sodium hypochlorite (bleach) diluted in  
water. Air dry all parts thoroughly before use.  
s NOTICE: Do not use phenolic products to clean the  
bubble pad.  
s NOTICE: After cleaning, air dry the bubble pad without  
direct exposure to sunlight.  
GENERAL MAINTENANCE  
1. Check main power cord for abrasion or excessive wear.  
2. Check bubble pad for signs of wear or damage. Ensure  
air tubes are firmly secured to bubble pad and pump  
connectors.  
3. Check the air tubes for kinks or breaks. For  
replacement, please contact your Graham-Field  
authorized distributor.  
12  
AQ1000-INS-LAB-RevD13  
 
Fuse replacement (220V system only)  
tool needed: small screwdriver  
1. If you suspect a blown fuse, disconnect the plug from  
the wall outlet immediately.  
fuse  
fuse cover  
fuse location  
2. Use a small screwdriver to remove the cover of the fuse  
holder (fuse locations are shown in picture above).  
3. Insert a new fuse of the correct rating (T1A/250V).  
4. Replace the fuse holder cover. Ensure that fuse holder  
cover is securely installed.  
STORAGE  
1. Fold the bubble pad loosely.  
2. Store bubble pad and pump in a dust-free environment  
with no exposure to direct sunlight.  
AQ1000-INS-LAB-RevD13  
13  
 
SPECIFICATIONS  
Model  
AQ1000 (Standard)  
AQ2000 (Deluxe)  
120V: 120V AC, 60 Hz, 1A  
Power Supply  
220V: 230VAC, 50 Hz, 7W  
120V: N/A  
Fuse Rating  
220V: T1A, 250V  
1.9 psi (13.10 kPa)  
1.0 - 2.0 psi (6.89-13.79 kPa)  
Pressure  
120V: 4.5 LPM  
220V: 5.0 LPM  
120V: 4-5 LPM  
220V: 5-6 LPM  
Air Output  
120V: 5 min.  
Cycle Time  
220V: 6 min.  
10 ft. (304.8 cm)  
Power Cord  
Length  
8.5 x 4.25 x 3.62 in.  
(21.59 x 10.80 x 9.19 cm)  
9.75 x 5.12 x 3.88 in.  
(24.77 x 13.00 x 9.86 cm)  
Pump Unit Size  
2.9 lb. (6.38 kg)  
3.5 lb. (7.7 kg)  
Pump Unit Weight  
78 x 34 x 2.5 in.  
(198.12 x 86.36 x 6.35 cm)  
76 x 34 x 2.5 in.  
(193.04 x 86.36 x 6.35 cm)  
Bubble pad Size,  
Inflated  
275 lb. (125 kg), EVENLY DISTRIBUTED  
Weight Capacity  
14 GA anti-bacterial, flame-retardant vinyl  
Bubble pad  
Material  
2 each: 5 ft. (152.4 cm) long clear PVC  
Tubing  
Contact your Graham-Field dealer or visit Graham Field's  
Replacement  
Parts  
Info: Specifications are subject to change without notice.  
14  
AQ1000-INS-LAB-RevD13  
 
WARRANTY  
GF Health Products, Inc. warrants the Lumex AQ1000 /  
AQ2000 Alternating Pressure Pad and Pump System for  
defects in workmanship and materials for the terms listed  
below.  
Pump: one year  
Pad:  
90 days  
If a product is deemed to be under warranty, GF Health  
Products, Inc. shall provide, at its option, (1) replacement  
of any defective part or product or (2) a credit of the  
original selling price made to GF Health Products, Inc.’s  
initial customer. The warranty does not include any labor  
charges incurred in replacement part(s) installation or  
any associated freight or shipping charges to GF Health  
Products, Inc.  
The warranties contained herein contain all the  
representations and warranties with respect to the  
subject matter of this document, and supersede all  
prior negotiations, agreements and understandings with  
respect thereto. The recipient of this document hereby  
acknowledges and represents that it has not relied on any  
representation, assertion, guarantee, warranty, collateral  
contract or other assurance, except those set out in this  
document.  
AQ1000-INS-LAB-RevD13  
15  
 
GF Health Products, Inc.  
2935 Northeast Parkway  
Atlanta, Georgia 30360  
tel: 770-368-4700  
fax: 770-368-2386  
© 2008 GF Health Products, Inc.  
 

Kuppersbusch USA Coffeemaker EKV 68000 M User Manual
KWC Indoor Furnishings K12H111000 User Manual
Learning Resources Car Amplifier LER 4403 User Manual
Lenmar Enterprises Cell Phone Accessories PPUS20 User Manual
LG Electronics Scale QHW 15 User Manual
Liebherr Ice Maker 280813 User Manual
LST Network Card 55000 588 User Manual
Mattel Motorized Toy Car Y9172 0920 User Manual
Melissa Juicer 244 001 User Manual
Metz Flat Panel Television 20 TM 52 User Manual