Magma Gas Grill A10 1225 User Manual

OWNER’S MANUAL  
Gourmet Series Marine Gas Grill  
Model A10-1225  
For questions regarding performance, assembly,  
operation, parts, or returns, contact the experts  
at MAGMA by calling TOLL FREE IN U.S.A. AND  
CANADA 1-800-86-MAGMA  
7:00 a.m. - 5:00 p.m. Pacific Time Monday thru  
Friday or e-mail us at [email protected]  
Read all instructions before operating. Save manual for future reference.  
 
MOUNT HARDWARE  
Fasteners are supplied for both Single Mount and Dual Mount grill mounting  
options. See Magma Catalog or Website for best mount selection.  
Single mount through-bolt  
applications  
4 Carriage bolts & lock nuts.  
Dual mount applications  
4 Carriage bolts & lock nuts. Only 4 bolts  
required for grill mounting. Place bolts (2 per  
side) diagonally from each other as shown.  
Single mount non-through-bolt  
applications, including Style 1 “Levelock”  
4 Hex head bolts & lock washers.  
Carriage bolt  
& lock nut  
Hex head bolt  
& lock washer  
ON-BOARD FUEL SYSTEMS APPLICATION  
•For on-board LPG (Propane) Systems, use Magma Type 3-High Output-  
Low Pressure LPG Control Valve and Magma Low Pressure LPG Hose Kit.  
•For on-board CNG (Natural Gas) Systems, use Magma Type 4-High Output-  
Low Pressure Natural Gas Control Valve.  
See Magma website for  
replacement part numbers  
and valve applications.  
Thermometer  
Lid Lock  
Warming Rack  
Grill Grates  
Burner  
Radiant Plate  
Liner  
Outer Shell  
Match Light  
Hole  
Valve Chamber  
Control Valve Regulator  
Type 1 High-  
Output Shown  
Mount  
Support Pad  
Slide Out  
Grease Tray  
Piezo Igniter  
3
 
OPERATING PROCEDURES  
OPERATE ONLY ON “LOW” WHEN LID IS CLOSED.  
ALWAYS OPERATE WITH GREASE TRAY IN PLACE.  
WARNING: Do not overheat grill. Magma Grills do not require pre-heating.  
Stainless Steel loses anti-corrosive characteristics when subjected to extreme  
heat. Most grilling is done on low temperature with the lid closed. If medium  
or high heat is required, grill with lid open.  
LIGHTING INSTRUCTIONS  
• Open lid during lighting.  
• Depress knob and rotate counter-clockwise to the “HIGH” flame  
• Push Piezo Igniter.  
position.  
• Visually confirm ignition through match light hole.  
• Turn knob to adjust flame.  
• If grill does not light, repeat process.  
MATCH LIGHTING INSTRUCTIONS  
• Open lid during lighting.  
• Depress knob and rotate counter-clockwise to the “HIGH” flame  
• Hold match or gas flame long lighter up to the match light hole.  
• Visually confirm ignition through match light hole.  
position.  
TO REDUCE FLARE-UP  
• Empty and clean grease tray prior to each use.  
• Trim excess fats from meat.  
• Use non-oil based marinades.  
• Reduce heat.  
• Use water spray directly on flare-ups.  
NOTE: Before lighting, lid lock must be positioned not to engage. Open lid  
and turn lock to locked position, or bring lock latch up to handle in open  
position and flip lock actuator back onto handle.  
PRACTICAL HINTS:  
Before lighting your grill, be sure that …  
Grill is secure and properly mounted.  
Internal components and grease tray are clean and correctly positioned.  
You have plenty of gas in the canister.  
Gas canister is attached properly and there are no gas leaks.  
Lid lock has been set not to engage.  
You have a water spray bottle handy to cool a hot grill or stop any flare-ups.  
STOWING TIPS  
• Always disconnect the fuel canister from the valve prior to stowing.  
• Stow the valve in a clean, dry area to protect from corrosion to valve.  
Always store propane in a sealed propane storage locker that allows leakage  
to vent overboard or use Magma A10-210 Propane Storage Tote.  
Never stow below decks  
4
 
ELECTRODE SPARK ADJUSTMENT  
CAUTION: Spark can cause small shock. Do not leave  
fingers on or near electrode wire while engaging igniter.  
• Electrode wire should be approximately 1/8” from gas  
exit hole in burner. Carefully adjust wire if required.  
A
DISASSEMBLY & RE-ASSEMBLY  
Lift radiant plate up & out of left slot (see B) and remove by sliding it out  
of right slot (see C).  
Remove burner screw (see B) and remove burner. Check burner for grease  
residue or spider webs that may obstruct gas flow. CAUTION: WHEN  
REPLACING BURNER, CUT SLOT IN BURNER MUST FACE DOWN.  
To remove liner from outer shell you must disconnect the electrode wire  
(see D). First remove the two screws on valve chamber (see D) and remove  
the cover plate. Gently pull wire off connector (see D). It is not necessary to  
remove electrode from liner.  
Remove Lid and liner by removing hinge screws and lock nuts with 3/16”  
hex key wrench (supplied) and 1/2” wrench or pliers. CAUTION: LOCK NUTS  
MUST BE INSTALLED WITH LOCKING INDENT MARKS SHOWING (see E).  
IMPROPER INSTALLATION WILL DAMAGE THE HINGE SCREW AND LOCK NUT.  
Lift liner out of outer shell by lifting up on liner lip on back side of liner  
(see F). When replacing liner, be sure top lip of liner installs over top edge  
of outer shell (start with corners of lip and work in).  
• Inspect burner, remove any obstructions.  
• Clean as indicated in Maintenance (page 6).  
• To re-assemble, reverse the procedure.  
Disconnect wire  
B
D
C
Right  
side  
slot  
Left  
side  
slot  
Electrode  
Screws  
Burner screw  
F
E
Liner Lip  
Liner  
Outer Shell  
Locking  
Indents  
5
 
MAINTENANCE  
About Stainless Steel - Stainless steel exposed to prolonged periods of high heat will change  
color and texture. Magma grills require no preheating. Not preheating will keep your grill cooler  
and greatly extend the life and beauty of your grill. Texture and color change is normal on  
interior components and will not affect the products operation or performance.  
Exterior Stainless Steel Components - Cleaning the exterior surface after every use will help  
prevent discoloration. Use soapy water with a soft cloth or sponge. Rinse thoroughly with fresh  
water and dry. We recommend covering the grill between uses. Optional covers are available  
from Magma retailers or direct from Magma. CAUTION: ABRASIVE PADS OR CLEANERS WILL  
DAMAGE THE FINISH.  
Interior Components - Remove heavy residue from grill and empty grease tray between  
each use. We recommend complete disassembly and cleaning at least once a year depending  
on amount of use (see page 5) and always prior to long term storage. For burnt-on residue we  
recommend Easy-Off brand Oven & Grill Cleaner. If cleaner is used on liner or lid, complete  
disassembly is recommended to remove any cleaner residue left between components. Wash  
all components with soapy water after using cleaner. CAUTION: AVOID CONTACT OF IGNITER  
AND ELECTRODE WIRE AND WIRE CONNECTORS WITH OVEN CLEANER.  
Grill Grates - Clean with brass wire brush while grill is warm. Use Oven & Grill cleaner for  
burnt-on residue. Wash with soapy water and dry prior to storage.  
Ceramic Electrode - Located just beside the burner, it should be kept clean of grease and  
debris. Be careful not to damage the ceramic insulation or bend the wire. See page 5 for  
electrode spark adjustment.  
Control Valve - All valves are set and tested at our factory. Do not attempt to adjust or  
disassemble the valve in any way. Call Magma if you suspect it is not adjusted properly. Clean  
valve with a cloth and remove any debris obstructing the gas outlet orifice using a pin or needle.  
Repair/Replacement Parts - See Magmas Website for a complete list of Repair or  
Replacement Parts. www.MagmaProducts.com  
USING GRILL WITH ON-BOARD LPG (PROPANE) SYSTEMS  
• Magma On-Board LPG (Propane) Valves  
and Hose Kits allow Magma Grills to be  
installed within a boats existing on-board,  
pre-regulated low pressure LPG (Propane)  
system.  
Gourmet  
Gas Grill  
Gourmet  
Gas Grill  
Type 3  
Valve  
Align valve stem key  
to valve chamber  
lock detent and rotate  
• Use only Magma Type 3 Low  
Pressure LPG (Propane) Valves. See  
our Valve Application Guide at www.  
MagmaProducts.com for correct valve.  
• In North America use Magma A10-225  
LPG 10' Hose Kit in conjunction with  
Type 3 Valve. Outside North America check  
your local dealer for proper hose and fittings.  
• A primary shutoff valve (supplied with  
A10-225 hose kit) must be used with this  
control valve at point of connection into  
your system. This allows shut off of gas  
supply to hose leading to grill.  
Gourmet  
Gas Grill  
Type 3  
Valve  
Typical Marine &  
R.V. Application  
Cylinder Valve  
Gauge  
Solenoid  
Shut off  
valve  
To other LPG  
appliance  
or use cap  
Gas Regulator  
Propane (LPG)  
A10-225  
Hose Kit  
6
 
TROUBLE SHOOTING GUIDE  
Problem  
Possible Cause  
Possible Solution  
Burner will not  
light with igniter  
Igniter electrode covered with  
grease or residue  
Clean igniter electrode  
Igniter/electrode too far from  
burner  
Adjust electrode until proper  
spark appears (see page 5)  
Igniter/electrode wire loose or  
disconnected  
Reconnect wire between  
igniter & electrode (see page 5)  
Wire is shorted causing spark  
from wire before electrode  
Call Magma  
No spark being generated  
No gas flow  
Call Magma  
Burner will not  
light even with  
match  
Check fuel level, refill cylinder  
or replace canister  
Obstructed gas flow/debris or  
spider webs in burner tube  
Clean valve orifice and burner,  
check all lines (see page 6)  
Flare-up  
Excessive cooking temperature  
Operate only on low when  
lid is closed  
Reduce flame level  
Leave lid open  
Use water spray to cool  
Grease and/or residue build-up  
Excessive fat in meats  
Clean components  
Trim fat from cuts of meat  
before grilling  
Excessive oils in marinades  
Use non-oil based marinades  
Yellow sooty flame  
Blow-out  
Obstructed gas flow/debris or  
spider webs in burner tube  
Check and clean valve orifice  
and burner (see page 6)  
Flame too low  
Increase flame  
Wind directly on burner  
Obstructed gas flow  
Block wind when opening lid  
Clean burner or valve orifice  
(see page 6)  
7
 
Contents  
A
x 4  
x 4  
B
C
A) (1) 3/16” Hex key wrench for lid removel.  
B) Pack of (4) 1/4”-20 x 5/8” hex head screws  
and internal lock washers for “Levelock” single  
mount application.  
x 4  
x 4  
C) Pack of (4) 1/4”-20 x 5/8” carriage bolts and  
lock nuts for dual mount and single mount  
applications and table legs.  
LIMITED WARRANTY  
Magma Products, Inc. guarantees this gas grill to be free from defects in materials or workmanship to the original consumer. This guarantee is for the periods  
herein specified when used under normal and reasonable conditions, one (l) year from the date of original purchase. This warranty does not include the cost of  
property damage or any inconvenience due to the failure of the product. Nor does it cover damage due to misuse, abuse, accident, or damage resulting from  
transportation of the product. Nor does it include damage resulting from the commercial use of this product. If the product fails to operate due to a defect in  
materials or workmanship during the warranty period, the defective part will be repaired or replaced at Magma's option. If you wish to obtain performance under  
this limited warranty, you should contact Magma's Customer Service Department via telephone at 562-627-0500 or 800-86-MAGMA, or via e-mail at  
[email protected], or via U.S. Postal Service mail at “Magma Products, Inc., attention Customer Service, 3940 Pixie Ave. Lakewood, CA, 90712.“ The defective  
part, along with proof of purchase, must be returned postage prepaid to Magma Products, Inc. We suggest that you keep your purchase receipt as we may require  
reasonable proof of purchase.  
In the state of California only, if refinishing or replacement of the product is not commercially practicable, the retailer selling the product, or Magma Products,  
Inc., will refund the purchase price paid for the product, less the amount directly attributable to use by the original consumer prior to the discovery of the  
nonconformity. In addition, in the state of California only, you may take the product to the retail establishment from which it was purchased or to any retail  
establishment selling this product in order to obtain performance under this warranty.  
All implied warranties, including the implied warranties of merchantability and fitness for a particular purpose, are limited in duration to the express warranty  
periods specified herein for the parts described herein.  
Some states do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you. Neither Magma dealers, nor the  
retail establishment selling this product has any authority to make any warranties or to promise remedies in addition to or inconsistent with those stated above.  
Magma's maximum liability shall not exceed the purchase price of the product paid by the original consumer. Some states do not allow the exclusion or limitation of  
incidental or consequential damages, so the above limitation or exclusions may not apply to you. The warranty gives you specific legal rights and you may also have  
other rights which vary from state to state.  
MAGMA and the Magma logo are registered trademarks of Magma Products, Inc.  
Monterey is a trademark of Magma Products, Inc.  
Patent pending.  
CALIFORNIA PROPOSITION 65 – WARNING – The burning of gas cooking fuel generates some by-products, which are on the list of substances,  
which are known by the State of California to cause cancer or reproductive harm. California law requires businesses to warn customers of  
potential exposure to such substances. To minimize exposure to these substances, always operate this unit according to the use and care  
manual, ensuring you provide good ventilation when cooking with gas.  
Magma Products, Inc.  
3940 Pixie Avenue, Lakewood, CA 90712 • USA  
Phone (562) 627-0500 • e-mail: [email protected]  
 

LevelOne Switch FSW 1621 User Manual
LG Electronics Microwave Oven MS1949G User Manual
LG Electronics Projection Television Z44SZ80 User Manual
Lochinvar Swimming Pool Heater ERN User Manual
Lochinvar Water Heater 6 120 User Manual
LOREX Technology Indoor Furnishings MNT1721PR1 User Manual
Mackie DJ Equipment SR244 User Manual
Magnasonic Microwave Oven MMW6101 User Manual
Metz Camcorder Astral MF 63 TG 63 100 MT Spectral MF 55 TG 68 100 MT Nordkap S 70 TG 73 100 MT Stratos SF 72 TG 85 100 MT Linos S 84 TG 87 100 MT User Manual
Meyer Sound Computer Monitor X 10 User Manual