Metra Electronics Automobile Accessories 99 7402 User Manual

INSTALLATION INSTRUCTIONS FOR PART 99-7402  
APPLICATIONS  
Nissan  
350Z 2003-2005  
99-7402  
KIT FEATURES  
• DIN Radio Provision with pocket  
• ISO Radio Provision with pocket  
• Two stacked ISO units provision  
• Double DIN radio provision  
KIT COMPONENTS  
A) Radio Housing with Pocket B) Double DIN Trim-plate C) ISO Spacer Brackets D) ISO Snap-in Brackets E) ISO Trim-plate  
A
B
C
D
E
TOOLS REQUIRED:  
Panel Removal Tool or  
Small Flat Blade Screwdriver  
Phillips Screwdriver  
1-800-221-0932  
© COPYRIGHT 2004 METRA ELECTRONICS CORPORATION  
 
DASH DISASSEMBLY  
99-7402  
NISSAN 350Z 2003-2005  
Disconnect the negative battery  
terminal to prevent an accidental  
short circuit.  
1
2
A
For vehicles with automatic trans-  
mission, Unsnap and remove smaller  
trim-ring from around shifter.  
(Figure A)  
For vehicles with manual transmis-  
sion, Unscrew and remove shifter  
knob. (Figure A)  
B
3
4
Unsnap and remove center console  
trim panel including climate controls.  
(Figure B)  
C
For vehicles with navigation, Unsnap  
and remove navigation switch panel.  
(Figure C)  
D
5
For vehicles without navigation,  
remove pocket mat, then remove  
two screws that secure switch  
mask. (Figure D)  
1
 
DASH DISASSEMBLY  
99-7402  
NISSAN 350Z 2003-2005  
6
Remove (2) screws above the radio  
and (2) screws below the radio. Also  
remove (2) screws securing the  
E
radio/trim panel assembly. (Figure E)  
7
Unplug and remove the radio / trim  
panel assembly. (Figure F)  
F
8
9
Remove (4) screws securing the  
radio to the trim panel and remove  
the radio.  
Remove (8) screws securing the  
factory brackets to the radio and  
remove the brackets from the  
radio. (These brackets are required  
for stacked ISO and double DIN  
installations. You can skip this step  
for DIN or ISO installations with  
pocket).  
Continue to kit assembly.  
2
 
KIT ASSEMBLY  
99-7402  
DIN MOUNT RADIO PROVISION WITH POCKET  
A
1
2
Slide DIN cage (supplied with radio)  
into the radio housing from the front.  
(Figure A)  
Secure DIN cage to radio housing by  
bending the locking tabs outward.  
(Figure A)  
B
3
Slide the radio into the DIN cage until  
it snaps into place. (Figure B)  
Attach the radio / housing assembly  
to the radio trim panel using the  
factory screws removed during  
disassembly. (Figure C)  
4
C
Continue to final assembly.  
3
 
KIT ASSEMBLY  
99-7402  
ISO MOUNT RADIO WITH POCKET  
A
Align the holes in the ISO brackets with  
the holes in the radio. Mount the  
brackets to the radio using screws  
supplied with the radio. (Figure A)  
1
Slide the radio bracket assembly into  
the radio housing until it snaps into  
place. (Figure B)  
2
3
B
Snap the ISO trim-plate onto the front  
of the assembled radio and housing.  
(Figure B)  
C
4
Attach the radio / housing assembly  
to the radio trim panel using the  
factory screws removed during  
disassembly. (Figure C)  
Continue to final assembly.  
NOTE: To remove the radio unsnap and  
remove the ISO trim-plate. Using a flat  
blade screwdriver disengage ISO  
brackets from the radio housing and  
slide radio out of radio housing.  
4
 
KIT ASSEMBLY  
99-7402  
DOUBLE DIN RADIO  
Cut and remove center divider from  
double DIN trim-plate. (Figure A)  
1
2
A
Place the double DIN trim-plate on  
the front of the radio. (Figure B)  
3
Place one of the ISO spacer brackets  
and the right factory mounting  
bracket (Removed from radio during  
disassembly) on the right side of the  
radio. (The spacer bracket should be  
between the radio and the factory  
bracket.) Align the pins on the trim-  
plate with the holes on the factory  
bracket and mount the factory  
B
bracket to the radio using screws  
supplied with the radio. (Figure B)  
4
Place one of the ISO spacer brackets  
and the left factory mounting bracket  
(removed from radio during disas-  
sembly) on the left side of the radio.  
The spacer bracket should be  
between the radio and the factory  
bracket. Align the pins on the trim-  
plate with the holes on the factory  
bracket and mount the factory  
C
bracket to the radio using screws  
supplied with the radio. (Figure B)  
5
Attach the radio bracket assembly to  
the radio trim panel using the  
factory screws removed during  
disassembly. (Figure C)  
Continue to final assembly.  
5
 
KIT ASSEMBLY  
99-7402  
TWO STACKED ISO MOUNT UNITS  
Place the double DIN trim-plate on  
the front of the two ISO units.  
(Figure A)  
1
2
A
Place one of the ISO spacer brackets  
and the right factory mounting  
bracket (Removed from radio during  
disassembly) on the right side of the  
ISO units. (The spacer bracket  
should be between the ISO units and  
the factory bracket.) Align the pins  
on the trim-plate with the holes on  
the factory bracket and mount the  
factory bracket to the ISO units using  
screws supplied with the radio.  
(Figure A)  
B
3
Place one of the ISO spacer brack-  
ets and the left factory mounting  
bracket (Removed from radio during  
disassembly) on the left side of the  
ISO units. (The spacer bracket  
should be between the ISO units  
and the factory bracket.) Align the  
pins on the trim-plate with the  
holes on the factory bracket and  
mount the factory bracket to the  
ISO units using screws supplied  
with the radio. (Figure A)  
4
Attach the assembled units and  
brackets to the radio trim panel using  
the factory screws removed during  
disassembly. (Figure B)  
Continue to final assembly.  
6
 
FINAL ASSEMBLY  
99-7402  
FINAL ASSEMBLY  
Locate the factory wiring harness in the dash and make the connection as shown.  
Metra recomends using the proper mating adapter and making the connections as  
shown. (Isolate and individually tape off the ends of any unused wires to prevent  
electrical short circuit.)  
1
Re-connect the negative battery terminal and test the unit for proper operation.  
Reassemble radio and dash assemblies in reverse order of disassembly.  
2
3
FINAL WIRING CONNECTIONS  
Make wiring connections using the EIA color code chart shown below and the instructions included with the head  
unit. Metra recommends making connections as shown below; Strip, Splice, Solder, Tape. Isolate and individually  
tape off ends of any unused wires to prevent electrical short circuit.  
A
A)  
B)  
C)  
D)  
Strip wire ends back 1/2"  
Twist ends together  
Solder  
B
C
D
Tape  
METRA / EIA WIRING CODE  
12V Ignition / Acc . . . Red  
Right Front (+) . . . . . Gray  
12V Batt / Memory . . Yellow  
Ground . . . . . . . . . . . Black*  
Power Antenna . . . . . Blue  
Right Front (-). . . . . . Gray / Black  
Left Front (+) . . . . . . White  
Left Front (-). . . . . . . White / Black  
Right Rear (+). . . . . . Violet  
Amp Turn-On . . . . . . Blue / White  
Amp Ground . . . . . . . Black / White  
Illumination. . . . . . . . Orange  
Dimmer . . . . . . . . . . Orange / White  
Right Rear (-) . . . . . . Violet / Black  
Left Rear (+). . . . . . . Green  
Left Rear (-) . . . . . . . Green / Black  
*NOTE: When a Black wire is not present, ground radio to vehicle chassis.  
All colors may not be present on all leads due to manufacturer’s specifications.  
7
 
99-7402  
NOTES  
8
 
99-7402  
NOTES  
9
 
99-7402 INSTRUCTIONS  
1-800-221-0932  
© COPYRIGHT 2004 METRA ELECTRONICS CORPORATION  
INST99-7402  
REV. 05/05/06  
 

Lenoxx Electronics CD Player CD 162 User Manual
Lenoxx Electronics Thermostat Touchscreen Thermostat User Manual
Lexar Media CD Player LDP 400 User Manual
Life Fitness Fitness Equipment ST05 User Manual
Loewe Work Light Xelos 32 LED User Manual
Magnadyne Headphones Digital Headphones User Manual
Makita Power Screwdriver 6832 User Manual
Marantz CD Player DR4160 User Manual
Mark Feldstein Assoc Home Theater System SP4080 User Manual
Maytag Clothes Dryer W10443045B User Manual